● Adopt MT7621A+MT7905DAN+MT7975DN solution
● 2.4G, 5G dual-band dual-band support WIFI6, backward compatible with WIFI5 and WIFI4
● 1*100/1000Mbps WAN port, 3*100/1000Mbps LAN port;
● Adopt 12V/1A power adapter
● Support one-key reset, WPS one-key connection to WIFI networking
● 256MB memory + 128MB Flash large storage design
Product name | Wifi6 Gigabit Dual Band Router | |
Dimensions | 215mm（L）x 138mm（W）x 34mm（H） | |
Network side interface | WAN:1*GE | |
User side interface | Ethernet interface | 1~4 GE |
WLAN interface | 2.4GHz 802.11ax（2X2）+ 5GHz 802.11ax（2X2） | |
Hardware Metrics | CPU | MT7621A：MIPS1004Kc（880MHz，Durl Core） |
FLASH capacity | NAND FLASH 128MB | |
RAM capacity | DDR3 256MB | |
2.4G/5G WIFI | MT7905DAN+MT7975DN | |
Maximum power consumption | 10W | |
Recommendations | l The product should be kept away from objects that affect the wireless signal transmission of the antenna, such as metal objects, mirrors and other highly reflective objects; l Keep products away from sources of interference (wireless routers, microwave ovens, wireless phones, Bluetooth products, and data centers that generate a lot of high-frequency noise); l The product should be installed on the same floor of the use area as much as possible, and try to avoid using it on other floors; l Do not stack items on the product, and minimize the obstacles between the product and the receiving product l When the product is placed flat, the position should not be too high, and the recommended height is between 1.2m and 1.5m; l The product should be placed as flat as possible in the middle of the use area, and try to avoid placing it in the corner of the use area. | |
11ax WLAN throughput requirements | ||
Frequency band（Hz） | Bandwidth setting（Hz） | The throughput requirement is not less than（Mbps） |
2.4G | 20 | 140 |
40 | 280 | |
5G | 20 | 140 |
40 | 280 | |
80 | 560 | |
160 | 950 | |
Switches and Keys | Switch | None |
Button | RESET/WPS multiplexing button: short press for 2 seconds to start WPS, long press for more than 8 seconds to restore factory settings Link button: Press and hold for more than 5 seconds for the mesh to take effect. | |
LED lights | Quantity | 1 green light, 1 red light |
Status indication | Steady red light: normal power-on and no internet connection Blinking red light: And-Link networking is in progress Steady green light: Internet connected, no data transfer Blinking green light: Internet connected and data transfer available | |
Power Adapter | 12V/1A | |
Environmental requirements | Temperature ℃ | -5~40 |
Relative humidity | 10~95 | |
Atmospheric pressure（KPa） | 89~106 | |
Certification | 3C certification and SRRC certification | |
Reliability | MTBF（The mean time between failures) should be at least 30,000 hours, and there should be no business interruption or performance degradation during long-term operation. | |
Protection ability | The device power supply has the protection capability of 4KV (differential mode and common mode); the Ethernet interface has the protection capability of 1.5KV (common mode). | |
Software specification requirements
Base | -Quick Settings -Wireless Settings -And-Link Settings - Parental Control - Guest Network - Smart QoS |
Network | -Internet settings -LAN settings -DDNS -IPTV -IPv6 |
Wireless | -Wireless Settings -Guest Network -Access Control -WPS -Advanced Settings |
Settings management | - Routing table - Routing settings - IP/MAC binding |
Security Settings | -IP/Port Filtering -MAC Filtering -URL Filtering |
NAT forwarding | -Port forwarding -DMZ settings -VPN penetration |
Serve | -Remote management -UPnP -Scheduled reboot |
Tool | -Modify password -Time setting -System configuration -Firmware local upgrade -Ping diagnostics -Route trace - System log |
Operating mode | -Gateway mode - Bridge mode - Relay mode |
Other functions | -LED lights show on and off |
+86-755-2751 6288
